Showing 17–32 of 64 results

• 

  Magnetic Horizontal Float Switches

  Magnetic Horizontal Float Switches

  You need to trust that your level switches won’t let you down. Mobrey float level switches are rugged, robust, and trusted globally for their long-term reliability in the harshest of environments and the most hazardous areas. Ideal for industrial applications such as pump control and high or low alarm duty on tanks and pressure vessels.

  Buy now from our new self-service channel»

  Categories: Level, Mobrey, Product class, Switches
  Mobrey Switches
• 

  Suspended Solids Monitoring – MSM400

  Suspended Solids Monitoring – MSM400

   

  The Delta Mobrey MSM400 system continuously measures the suspended solids within sludges or slurries.  Many years of practical experience have shown that measurement of ultrasonic attenuation in a slurry is directly proportional to the percentage of suspended solids. The MSM400 system uses this principle to give a digital display and continuous output of the suspended solids measurement.

  Commonly used in waste water treatment, industrial and mining plants and suitable for a wide range of fluids such as effluent, limestone slurry and China clay.  Applications include sludge blanket measurement and detection, and slurry density control. The MSM400 controller is used with ultrasonic gap sensors available for either tank or pipe installation with a range of gap sizes to suit the application. View our webinar featuring the MSM400.

  Categories: Controller, Product class, Steam & Water
  On/Off and continuous monitoring of suspended solids
• 

  Vibrating Rod Level Switch for Liquids – VLS Switch

  Vibrating Rod Level Switch for Liquids – VLS Switch

  The Vibrating Rod Level Switch (VLS) is the perfect solution for single point level switching in free flowing solids.  For tanks, silos or hopper bins, and for a wide density range of solids from fine powders, grains to agregates. A single rod design provides the solution to tuning forks which may become blocked or bridged.

  The vibrating rod is energized and kept in resonance by an electronic circuit. When covered by material, the damping of the vibration is detected by the electronics which switch the output relay after a configurable time delay. The vibrating rod level switch is the perfect solution for single point level switching in free flowing solids across a wide density range, from fine powders to grains. A single rod design provides the solution to tuning forks which may become blocked or bridged.

  See more from our new self-service channel»

  Key Features

  • Adjustable sensitivity
  • 1 ½” BSP or NPT threaded connection
  • Side or top mounting
  • Extension lengths to 20m
  • Robust aluminium housing
  • IP67 ingress protection
  • AC or DC supply voltages
  • Dust explosion protection
  • High temperature option

  Categories: Level, Mobrey, Product class, Switches
  Stainless steel sensor, ATEX approved
• 

  Rotating Paddle Level Switch – PLS Series

  Rotating Paddle Level Switch – PLS Series

  The paddle switch may be used as either a high or low level limit switch. It is easily mounted from above, or through a vessel wall.  A small electric motor drives a paddle which rotates freely in the absence of material. When the paddle is impeded by the presence of material, a microswitch actuates an alarm signal. As soon as the paddle is completely stopped from rotating, power to the motor is cut, thereby extending motor life. After the material level falls, the motor is returned to its normal position and the paddle begins to rotate again.

  Failsafe models use a microcontroller for self-validating diagnostics and monitor both motor and shaft rotation to detect and indicate a fault condition on the fault relay.

  The PLS Series of switches can be used with granular, pelletized, and powdered dry products. They may be used in high level applications with materials over 160 kg/m3 and low or intermediate applications with materials over 80 kg/m3.

   

  Key Features

  • Failsafe option
  • High temperature option
  • 1½” BSP or 1¼” NPT threaded connection
  • Side or top mounting
  • Shaft or cable extensions
  • Robust aluminium housing
  • IP66 ingress protection
  • AC or DC supply voltages
  • Dust explosion protection

   

  Categories: Level, Mobrey, Product class, Switches
  Full option of available paddles, ATEX approved
• 

  Ultrasonic Level Switch – 003 Series

  Ultrasonic Level Switch – 003 Series

  The 003 sensor is a highly reliable level switch with no moving parts. It comprises of a one piece moulded body with an integral PCB, the 003 Level Switch is factory sealed and supplied with a flying lead for customer connection.
  The sensor is designed for high or low level alarm duties to give a voltage free contact or solid state transistor output for alarm signalling or as part of a pump control system. The Mobrey 003 switch is designed for high or low level alarm duties to give a voltage-free contact or solid state transistor output for alarm signalling or as part of a pump control system.

  Buy now from our new self-service channel»

  Key Features
  • Relay or solid-state output
  • Corrosion resistant PPS construction
  • 1-in. or ¾-in. threaded mounting
  • Small in-tank dimensions
  • 24 Vac or dc powered
  • Lightweight
  • No moving parts

  Categories: Level, Mobrey, Product class, Switches
  Low cost, universal installation, plastic body
• 

  MCU200 Suspended Solids Detection Switch

  MCU200 Suspended Solids Detection Switch

  The MCU controller and gap sensor when used together provide an ultrasonic point level liquid switch. Typical applications include sludge blanket level detection in settlement tanks, interface detection for immiscible liquids and contamination detection, such as oil in water or water in oil. The MCU201 and MCU203 control units provide simple and economical control electronics for wall-mounting near a tank or pipeline containing a single ultrasonic gap sensor. The sensors operate on the attenuation of an ultrasonic signal through the fluid. View our webinar featuring the MCU200.

  Categories: Controller, Mobrey, Product class, Steam & Water
  Mobrey Controller
• 

  Magnetic Level Switches – Vertical Series

  Magnetic Level Switches – Vertical Series

  For extreme conditions, this vertically mounted hermetically sealed switch provides dependable control.  Specifically designed to handle corrosive atmospheres and low temperatures, the magnet switch mechanism provides a positive snap shut action.  With less moving parts there is less maintenance and greater reliability.  This product is ATEX accredited.

  Key Features

  • No springs in switch mechanism – positive snap action switching
  • Vibration resistant – eliminates spurious trips
  • Multiple switch point options – cost effective control
  • Genuine hermetically-sealed switch option – totally safe and secure
  • Extensive range of chambers – suitable for most applications
  • Relevant chambers are supplied CE marked and fully compliant with the Pressure Equipment Directive (97/23/EC)
  • Designed to ASME B31.3
  • Weld procedures approved to EN ISO 15614-1 and ASME IX

   

  Categories: Level, Mobrey, Product class, Switches
  Mounted vertically, hermetically sealed
• 

  Hydratect 2462 System

  Hydratect 2462 System

  An electronic alternative to conventional water level switches for steam raising plants. Hydratect can be used in a wide variety of situations wherever the detection of water or steam is vital for the safe and efficient operation of a plant. The Hydratect 2462 control unit provides signal processing for two electrodes. Each channel monitors the status of its associated electrode. Four conductors are used between the control unit and each electrode so it can differentiate between steam, water, short-circuit and open-circuit. A green LED indicates water, a red LED indicates steam, and an amber LED indicates a fault condition. Each channel has a status relay to indicate water or steam, and a fault relay which will de-energise on a fault condition. The two channels are completely independent having separate power supplies, signal processing and fault detection. The relay outputs can be externally wired for a ‘one out of two’ or ‘two out of two’ tripping scheme.  A Hydratect 2462 system consists of electrodes which are fitted into inserts which are welded into the pipe work. Alternatively, manifolds can be supplied to drawing with inserts already in place. Electrodes are protected by covers. A military specification high temperature cable connects each electrode to the Hydratect control unit.

  A typical application to ensure TWIP (Turbine Water Induction Protection) is condensate level detection in drain pots (condensate pots).

  Hydratect can be used to give compliance with ASME TDP-1, Prevention of Water Damage to Steam Turbines Used for Electric Power Generation: Fossil-Fuelled Plants.

  Categories: Conductivity Probe, Product class, Steam & Water
  Conductivity Probe Steam and Water Detection
• 

  Hydrastep 2468 System

  Hydrastep 2468 System

  The Hydrastep 2468 is the modern day equivalent of the site glass to monitor, display and measure the output level of the water/steam interface. For use on water tube boiler steam drums and de-aerators, the Hydrastep name has become synonymous with steam drum level measurement, and through its evolution has ensured plant safety globally for more than five decades. Assessed by an external body and found to be SIL 2 capable, according to the requirements of IEC 61508. It is recognised by boiler inspectors and plant insurers, the ASME approved design ensures Hydrastep can be used as a Remote Level Indicator in compliance with ASME Boiler Code PG60.1.1. It is also approved by Factory Mutual for boiler level control and recommended within the UK’s Combustion Engineering Association’s water tube boiler guide BG11. All of this expertise is backed up by over 6000 installations of Hydrastep around the globe. For more information on this product view our webinar on Hydrastep’s involvement in the boiler industry!

  Key Features
  • For use with 8 to 32 electrode inputs
  • SIL 2 capable for use in a Safety Instrumented Function
  • High clarity local and remote displays
  • 32 segment green/red display of the water/steam interface level
  • 4–20 mA output proportional to water/steam interface level
  • Relay output option for high or low level alarms or trips
  • Dual redundancy option for ultimate reliability
  • Detect and indicate any fault conditions
  • Contamination indication for preventative maintenance
  • For use to 560 °C (1040 °F) and 300 Bar (4350 PSI)
  • PED compliant as a Safety Accessory
  • FM approved for boiler control
  • Hazardous area approved

  Categories: Conductivity Probe, Product class, Steam & Water
  SIL 2 Certified water level controls for boiler drums
• 

  Analogue Submersible Level Transmitters – 9700 Series

  Analogue Submersible Level Transmitters – 9700 Series

  The Delta Mobrey 9700 Series range of tank mounted transmitters provide you with precise and reliable level measurement solutions when in-tank foaming, vapor layers, and temperature gradients prevent use of other instrumentation. These transmitters are designed to perform in the extreme conditions of industrial applications. Available in submersible and externally mounted (floodable) versions, each transmitter gives you high performance and good long term stability, and is virtually maintenance free.

  Key Features

  • Factory sealed and tested for submersed duty
  • 4–20 mA output signal proportional to level
  • Flush mounted ceramic sensor
  • Good long term stability
  • Ideal for industrial or marine applications
  • Wide range of mounting options
  • Low cost installation
  • Readouts for control room or plant mounting

   

  Categories: Level, Mobrey, Product class, Transmitters
  Marine Certified, various installation options, CSA
• 

  GG Pressure Gauge

  GG Pressure Gauge

  The GG pressure gauge offers customer a cost-effective and accurate solution to their individual process requirements. It is manufactured in stainless steel, has a Bourdon Tube and is manufactured within the EU according to EN837 standards.

  • All stainless steel
  • Manufactured in the EU, according to EN837
  • Nominal Diameter options of 63, 100, 150, 200 and 250 mm
  • Degree of Protection IP55/IP67
  • Stainless steel enclosure as standard
  • Blowout Protection
  • Ranges available between -1 bar to 1000 bar
  • Monel pressure connection, material and options available

  Categories: Gauges, Pressure
  All stainless steel, Bourdon tube, manufactured in the EU
• 

  SG Pressure Gauge

  SG Pressure Gauge

  Manufactured in stainless steel within the EU, in accordance with EN837 standards. This product is designed for use in corrosive environments and is resistant to chemical attack.  The standard diaphragm material is stainless steel, AISI 316 Ti, but other materials are available upon request. The rugged SG range of diaphragm pressure gauges are suitable for a wide range of applications in industries such as Oil and Gas, Chemical, Petrochemical, Refining, Power and Marine.

  Key Features

  • Degree of Protection IP55/IP67
  • Nominal Diameter of 100 & 150 mm
  • Stainless steel enclosure as standard
  • Blowout Protection

  Categories: Gauges, Pressure
  Diaphragm Pressure Gauge, manufactured in stainless steel in the EU to EN837
• 

  Differential Pressure Gauge – DB Series

  Differential Pressure Gauge – DB Series

  All Stainless Steel execution, making it suitable for a range of applications in process plants and OEM equipment.  The robust nature of this product allows it to be used in hazardous areas, 1 and 2, to work with SIL2 safety related systems and corrosive atmospheres.  Like many Delta Mobrey products, this gauge can be modified should the customer require it.

  Key Features
  • Nominal Diameter of 100 mm.
  • Degree of Protection IP55/65/67.
  • Stainless steel enclosure as standard.
  • Ranges available between 1 and 60 bar.
  • Accuracy class 1.6%.

  Categories: Differential pressure, Gauges
  Double Bourdon Tube, 100, 150 options available, Manufactured in the EU
• 

  Analogue Level Probes – DSGE Series

  Analogue Level Probes – DSGE Series

  The DSGE-25/16 Hydrostatic Level Probes are designed to measure liquid levels in tanks, deep wells or narrow piezometers. The probe measures liquid levels, based on a simple relationship between the height of the liquid column and the resulting hydrostatic pressure. The pressure measurement is carried out on the level of the separating diaphragm of the immersed probe and is related to atmospheric pressure through a capillary in the cable.

  When lowered to the reference level, the probe may either hang freely on the cable or lie on the bottom of the tank. The cable with the capillary can be extended using a standard signal cable. For the cable connection a special DSG cable hanger is recommended.

  Key Features

  • 4–20 mA output signal proportional to level
  • Flush mounted ceramic sensor
  • Good long term stability
  • Ideal for industrial or marine applications
  • Wide range of mounting options
  • Low cost installation
  • Readouts for control room or plant mounting

  Categories: Approvals, D-Series, Level, Measurement, Product class, Series, Transmitters
  Transmitter suitable for clean water, seawater, sludge
• 

  D32 Analogue Differential Pressure Transmitter – D Series

  D32 Analogue Differential Pressure Transmitter – D Series

  The D32 Differential Pressure Transmitters is a cost effective solution for the measurement of differential pressure of gases, vapours and liquids. The active sensing element is a piezoresistive silicon sensor separated from the medium by a diaphragm and by a specially selected type of manometric liquid.

  The process connection to mount directly on to a 3 or 5 valve manifold, and also available is several type of chemical seals to measure any type of process fluid and condition.

  Key Features

  • Accuracy ±0.25%
  • 4-20mA output signal
  • Static pressure limit up to 420 bar
  • Gold plated diaphragm option, suitable for hydrogen based applications
  • Hastelloy C276 wetted parts option
  • Intrinsic safety certificate (ATEX, IECEx)

   

  Categories: Approvals, D-Series, Differential pressure, Measurement, Product class, Series, Transmitters
  Basic, low cost and robust
• 

  D22 Pressure Transmitter

  D22 Pressure Transmitter

  The D22 Pressure Transmitters are an economic solution for the measurement of pressure, underpressure, and absolute pressure of gases, vapours and liquids. Available in a wide range of blind and compact construction for a wide range of industrial applications.  The active sensing element is a piezoresistive silicon sensor separated from the medium by a diaphragm and by a specifically selected type of manometric liquid.

  This series is suitable for use in corrosive atmospheres and is also resistant to chemical attack. The model D22 Pressure Transmitter is suitable for measuring pressures from 0 to 25 mbar up to 0 to 1000bar with maximum overpressure up to 1200bar.

  Categories: Approvals, ATEX Ex d, ATEX Ex ia, D-Series, IECEx Ex d, IECEx Ex ia, Measurement, Pressure, Product class, Series, Transmitters
  Cost effective analogue transmitter, robust and fixed range
« 1 2 3 4 »